|
Who's Online
There currently are 6041 guests and 2 members online.
|
Categories
|
Information
|
Featured Product
|
|
|
|
|
There are currently no product reviews.
;
The service manual was a copy of the original from Wirlpool. The quality was good, all neccecary information was available including the service-codenumbers, so I could order the right part to be replaced for repair.
Downloding was no probem after the payment.
Thanks for the service!
;
Good,readable manual. I found other manuals that were not readable when it came to part ID, but the one downloaded from owner-manual.com was better than expected. I will do buisness with owner-manual.com again.
;
Service Manual that I received was very helpful to me. Thank you.
;
The manual is well organized and is easy to read. The chapters are following normal way to proceed.
;
This scanned manual is well done in that most all the pages except for one is straight and clear- the way I would do them. One page was upside down but that happens. For the money that is charged on this site you get a pretty good deal. Now with complex repairs, I still prefer to us paper manuals which I have to buy at stereomanuals but the one I got here was much less than the $45 he was charging but this is a larger than normal manual for three different units. I am a picky manual user because I have used original manuals from Sony and Teac.
XLR-10 Installation
First make sure that the CR-1604 is turned off. Flip it upside down with the jacks facing you (there is no need to actually remove the pod) and remove the small connector cover near the pod's center. Save the cover and screws by taping them to the bottom of the mixer. Remove the pod's rubber feet. 3 Install the ribbon connector which extends out of the XLR10 by pressing the plug onto the exposed pins. Make sure that the stripe on the ribbon is on the side closest to the XLR 10's phantom switch (the right side in our drawing).
2 1
Operating Instructions
When you combine the CR-1604 with the XLR10 you can use the added mic inputs by themselves or,mic and line inputs simultaneously. use both if you're starved for inputs, you can In other words, with the XLR10, you actually get 10 more inputs. On Channels 7 through 16 only, the XLR mic inputs can be used with the existing line inputs. Each has its own sensitivity control. Set the sensitivity controls as you normally would. Put the channel into SOLO to read its operating level on the main output meter. 1. Adjust the mic sensitivity control first . 2. With the mic placed where it will normally operate in relation to the acoustic source, start at minimum (fully counterclockwise), then turn the gain up until you get a reading of around 0dB on the meter. 3. Finally, adjust the line input sensitivity until you get the desired balance between mic and line signals.
As you lower the XLR10 towards the CR-1604 pod, work the excess ribbon cable back into the XLR10 by wiggling it gently.
5 Slide the tabs on the sides of the XLR10 into the slots on the top of the CR- 1604 and secure them with the four #8 screws provided. Don't push on the screws while attaching them, since doing so may dislodge the mounted nuts on the inside of the pod. 6 Install the new pod feet.
4
Happy mixing!
pod �foot�
2
connector cover
1
pod �foot�
2
C
R- 1 60 4
CR-1604 pod 48V phantom switch XLR10 tab A tab A slot B
3
stripe ribbon connector
slot B
Famous XLR10 Interview Questions
Q. Can the XLR10 be used in all of the three pod variations? A. Yes, see the drawing below. Q. Can the XLR10 be used with anything other than the CR-1604? A. No, it utilizes the internal power supply of the CR-1604 and is not free standing.
4
4.8" 0.7"
16.1"
3.8"
0.5"
5.9"
6.4"
pod �foot� #8 screws
pod �foot� #8 screws
15.8"
18.2"
5
5
5.9"
2.3"
12.0"
2.3"
2-4
POD BOARD 02 Rev N
©1994,©1999 Mackie Designs Inc. All rights reserved
|
|
|
> |
|