|
|
|
Who's Online
There currently are 6041 guests and
2 members online. |
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
This GRUNDIG UV5A Owner Manual is not only an instruction manual but a total functional circuit description of the Multimeter and includes circuit diagram at the end pages. It is very helpful for repairing and calibrating the instrument. It is written in two languages English and German for international support. It was very easy to repair my unit with this document. Regards, Regis Pauly, Electrical Engineer.
;
The owner's manual was evetything I thought it would be. I was able to print it out using both sides of the paper in quick order, saving me a search online for a used one.
 ;
Хорошее качество сканирования.
Мануал пришел часов эдак через 12. В целом доволен.
;
Fantastic quality and impressive delivery time. Based on this manual, I recommend this service without hesitation! Five Stars for certain.
;
Was happy to find the complete owners manual... It's all in there, just like the original...
SERVICE INFORMATION
Warranty Service
If you think your subwoofer has a problem, please do everything you can to confirm it before calling for service, including reading through the following Troubleshooting section. Doing so might save you from being deprived of your Mackie loudspeaker. Of all Mackie products returned for service (which is hardly any at all), many are coded �CND� � Could Not Duplicate� which usually means the problem lay somewhere else in the system. The following troubleshooting tips may sound obvious, but here are some things you can check: � Is the POWER/PROTECT LED lit red on the Fussion Series Active Speaker? Make sure there is at least six inches of free space behind the heatsinks.
Poor bass performance
� Check the polarity of the connections between the mixer and the loudspeakers. You may have your positive and negative connections reversed at one end of one cable, causing one loudspeaker to be out-of-phase.
Poor sound
� Is it loud and distorted? Make sure that you�re not overdriving a stage in the signal chain. Verify that all level controls are set properly. � Is the input connector plugged completely into the jack? Be sure all connections are secure. It�s a good idea to periodically clean all electrical connections with a non-lubricating electrical contact cleaner.
Troubleshooting
No power
� Our favorite question: Is it plugged in? Make sure the AC outlet is live (check with a tester or lamp). � Our next favorite question: Is the POWER switch on? If not, try turning it on. � Is the POWER LED on the rear panel glowing green? If not, make sure the AC outlet is live. If so, refer to �No sound� below. � Check the AC line fuse to see if it is blown. If so, make sure you replace it with the same fuse rating as indicated on the rear panel next to the fuseholder.
Noise
� Make sure all connections to the active loudspeakers are good and sound. � Make sure none of the signal cables are routed near AC cables, power transformers, or other EMI-inducing devices. � Is there a light dimmer or other SCRbased device on the same AC circuit as the FUSSION 1800SA? Use an AC line filter or plug the FUSSION 1800Sa into a different AC circuit.
No sound
� Is the input LEVEL control for the input source turned all the way down? Verify that all the volume controls in the system are properly adjusted. � Is the signal source working (and making union scale)? Make sure the connecting cables are in good repair and securely connected at both ends. Make sure the output volume (gain) control on the mixing console is turned up sufficiently to drive the inputs of the speaker. � Make sure the mixer does not have a Mute on or a Processor loop engaged. If you find something like this, make sure the volume/gain is turned down before disengaging the offending switch.
Hum
� Try disconnecting the cable connected to the MAIN INPUT jack. If the noise disappears, it could be a �ground loop,� rather than a problem with the FUSSION 1800SA. Try some of the following troubleshooting ideas: � Use balanced connections throughout your system for the best noise rejection. � Whenever possible, plug all the audio equipment�s linecords into outlets which share a common ground. The distance between the outlets and the common ground should be as short as possible.
9
|
|
|
> |
|
