|
|
|
Who's Online
There currently are 5845 guests online. |
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
Very well done!!!!! congratulations. It was a bit longer than usual the wiating time even if it was on time (in 24 hours).
;
Last week I bought a second hand BAUKNECHT TRK4850 DRYER. It is a professional machine with many programs and switch options. I feared it would be a huge quest to find a manual. I was delighted when I found owner-manuals.com. After payment I received the file to download the next day already. The quality is great. I am very happy. Thanks!
but kindly the distributions of the operating programs not find in the owners manual,can you help me to understand the operating programs instructions thank you
;
Very good copy, very readable and easy transaction as always.
;
It is perfect, exactly what we needed. It's like the paper version but less clutter.
 ;
Received my manual within 24 hours. Very clear scan of the manual I needed. Thanks!
Get that sound level meter out. Decide what level you�re going to mix at and use the meter to help keep you mixing at that level. Your ears will thank you, and your mixes will be better 10 for it.
The fuse is located behind the fuse cover, at the bottom of the IEC socket. See the �Troubleshooting� section on page 11 for information about replacing the fuse.
11
4. LOW FREQ Switch
The LOW FREQ switch tailors the overall low-frequency response by +2 dB or +4 dB at 65 Hz. � For most applications, use the �0 (NORMAL)� setting. This takes the equalization circuit out of the signal path. � If you want or need just a little extra lowfrequency output, use the +2 dB setting. � If you want or need more lowfrequency output, use the +4 dB setting. Remember how things work in reverse, so boosting the deep bass content on playback may actually decrease it in the �nal mix.
8. Bass Re�ex Port
A bass re�ex system uses the radiation from the rear of the woofer cone to extend the lowfrequency response of the speaker. The size of the port is carefully designed with respect to the volume of the cabinet and the characteristics of the woofer to produce lowfrequency extension.
9. Heatsink
The heatsink is designed to dissipate the heat generated by the built-in power ampli�ers. The cooler the ampli�ers operate, the longer their lifeexpectancy. The S�5 uses convection cooling, where cool air �ows through the �ns of the heatsink and carries the heat away. Make sure there is at least six inches clearance between the back of the S�5 monitors and the wall.
5. AC SELECT
Set this switch to the correct voltage setting for the country you are in, 115 VAC or 230 VAC. Note: The S�5s are shipped with the AC SELECT switch set to the 230 VAC position. If you are in a country that uses 100-120 VAC, set the switch to the 115 VAC position and replace the fuse (located in the IEC socket) with the 1.6 A fuse included in the accessory bag. See the �Troubleshooting� section on page 11 for instructions on replacing the fuse.
FRONT PANEL DESCRIPTION
10. Power LED
This illuminates when the POWER switch is turned on and AC power is available at the line cord socket.
11. Clip LED
This LED illuminates just before the low-frequency ampli�er reaches its maximum output and begins to clip. � Occasional blinking of the Clip LED indicates that the loudest transients are reaching the maximum output capability of the ampli�er. This is okay. � Frequent or continuous blinking of the Clip LED indicates that you have exceeded the maximum output capability of the ampli�er and that the ampli�er is clipping. You should reduce the level from your signal source until the Clip LED blinks occasionally or not at all.
6. POWER
Use this switch to turn the active monitors on and off.
7. Line Cord Socket and Fuse
Connect the line cord to this IEC socket securely, and plug the other end into your AC outlet. Make sure the AC SELECT switch is set to the correct AC voltage.
9
|
|
|
> |
|
